Life

CONTACTLESS DIGITAL TACHOMETER PDF

Simple but accurate digital tachometer using microcontroller Has a resolution of 1 rev/sec. The tachometer use an optical pickup scheme for picking . Today, we are going to make a digital tachometer based on a PIC This tachometer can measure speeds up to RPM with the resolution . Sir, I want the code for the Contactless Digital Tachometer using PIC16FA. Abstract: This paper proposes a hardware design of an. “Digital Contact-less Tachometer” based on IR sensor for measuring the Revolutions Per Minute (RPM ).

Author: Nikogor Mezill
Country: India
Language: English (Spanish)
Genre: Love
Published (Last): 28 May 2009
Pages: 152
PDF File Size: 1.66 Mb
ePub File Size: 14.8 Mb
ISBN: 791-9-51235-439-4
Downloads: 4342
Price: Free* [*Free Regsitration Required]
Uploader: Mikahn

The instruction CPL A will just complement the digit drive pattern in accumulator so that it becomes suitable for the common anode display. LCD tachometertachometer using Heart rate monitor with sms alert. Will be updated on this page.

The circuit diagram of the LCD tachometer using is given below. In the crystal frequency is divided by 12 using an internal network before applying it as a clock for the timer. You an use Keil to code, compile and test the program code. This is done just because to save my time but vigital a text book method. The usage of LTH photo interrupter module makes it more rugged and stable. Leave a Reply Cancel reply Your email address will not be published. We are working on the layout part!

The circuit diagram of the digital tachometer is shown below. For project purpose of dontactless a distance below 1meter is suitable, but higher distances are possible if sensors are properly calibrated.

  KNJIGA PROROKA DANILA PDF

Contactless digital tachometer using 3 digit display and measures upto rev/sec

I want to ask whether the mechanism in this project counts the pulses for 60 seconds and then display it if so then how to configure to delay time for 60 sec and at the same time count the pulses in that duration? Any special interface cable? Timer 1 is configured as an 8 bit auto reload counter for registering the number of incoming zero going pulses and Timer0 is configured as a 16 bit timer which generate the necessary 1 second time span for the Timer1 to count.

This is for my study and teaching the program how to srite Thanks a lot for the Originators. Digital tachometer using admin April 20, 39 Comments.

If possible would u digiyal furnish me with the PCB layout of the circuit of tachometer using given. Interfacing Nokia Display to Micro Controller Moisture sensing automatic plant watering system using Contactless digital tachometer using But this distance varies according to the climatic conditions in the region and also other tahcometer operating in the area.

I have a problem in the optical pick up assembly. Also, there is a change in the sensor circuit. Can you feed me thw same circuit with high sensitivity.

Embedded Lab

I have tested my T. I use an In system programmer ISP module for programming the Previous post Next post.

Dual supply opamps configured in single supply mode will not give results like a dedicated single cotactless opamp in the same situation. The working principle is almost similar to that of the previous version but the program is heavily modified. For the counting purpose both the timers of Timer0 and Timer1 are used. Digital tachometer using Thank you for all. V remote to operate properly from distance of 5m at the most, on a sunny day with average temperature of Kelvin. Tachlmeter this setup and every other setup based on principle of reflection of tachpmeter the IR LED and the photo-sensor are placed side-by-side at a distance of mm from each other facing the obstruction which is generally less than 10cm away from the tip of IR LED.

  FURCRAEA ANDINA PDF

From the above two graphs you can see that the negative going edge of the waveform indicates the passage of the reflective patch across the sensor and that means one revolution. Can this circuit be purchased on this site?

Next part is the signal conditioning unit based on the opamp LM IC1. You have to test and calibrate your sensors based on application. I used LM just because that was the only single supply opamp with me at the time.

Every time the collector voltage of the photo transistor goes below 3. C remotes use IR sensors to operate.

Military uses high grade IR sensors that are able to operate for distances of few 10Km tachomeher Km. What you use to program the ? When viewed through an oscilloscope the collector waveform of the photo transistor Q4 2N would look like this:.

The program actually counts the number of negative going pulses in 1.