Literature

ASTM D885 PDF

ASTM D – Air Permeability of Textile Fabrics . Reference: ASTM D – Standard Test Methods for Tire Cords, Tire Cord Fabrics, and Industrial Filament . ASTM D/DM: Standard Test Methods for Tire Cords, Tire Cord Fabrics, and Industrial Filament Yarns Made from Manufactured Organic-Base Fibers. This standard is issued under the fixed designation D ; the 1 These test methods are under the jurisdiction of ASTM Committee D13 on.

Author: Vubar Nikosho
Country: Sudan
Language: English (Spanish)
Genre: Software
Published (Last): 23 August 2004
Pages: 349
PDF File Size: 15.40 Mb
ePub File Size: 18.66 Mb
ISBN: 262-2-57204-182-2
Downloads: 29766
Price: Free* [*Free Regsitration Required]
Uploader: Ter

The r885 of this test is a determination of tensile strength of the cord being tested. Software for Series Systems. SI units is the technically correct name for the system of metric units known as the International System of Units. Contact Us View Accessories Catalog. Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience.

The values axtm in either acceptable metric units or other units shall be regarded separately as standard. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias. Glossary of Materials Testing Terms. Breaking Tenacity of Conditioned Yarns and Asgm. Email addresses can only contain letters, numbers and the following special characters: Active view current version of standard.

Onsite Training At Your Facility. Bibliography of Tire Cord Test Methods. Link to Active This link will always route to the current Active version of the standard. Historical Version s – view previous astj of standard Translated Version s: Adhesion of Cord to Elastomers.

  DVDR3455H MANUAL PDF

ASTM D885 Tire Cord Tensile Test

They are designed with standard and optional features that increase testing efficiency and improve the testing experience for the operator. Bluehill LE for Basic Testing.

We use cookies to improve your browsing experience. As a minimum, test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing.

It is important to review ASTM D to fully understand the test setup, procedure, v885 results requirements. The values expressed in each system may not be exact equivalents; therefore, each system must be used independently of each other, without combining values in any way.

Significance and Use, Tensile Properties. Width of Tire Cord Fabric. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. This standard may be applied to similar yarns and cords used for reinforcing other rubber goods astk for other industrial applications.

It is recommended that any program of acceptance testing be preceded by an interlaboratory check in the laboratory of the purchaser and the laboratory of the supplier on replicate specimens of the materials to be tested for each property or properties to be evaluated. Growth of Conditioned Yarns and Cords. Bluehill Universal Brochure Bluehill Universal Software is built from the ground-up for touch interaction and an intuitive user experience.

  ELISABETH ROUDINESCO FAMILIA DESORDEN PDF

ASTM D Industrial Filament Yarns Made from Manufactured Organic-Based Fibers – Instron

Twist in Yarns and Cords. Breaking Toughness of Yarns and Cords.

Gripping of the specimens can prove a challenge, as the cords tested with this standard are designed to be very high strength. The test methods apply to nylon, polyester, and rayon yarns and tire cords twisted from such yarns and to fabrics made from such cords.

Significance and Use, Asm. Subscribe to Instron News! Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.

Combining values from the two systems may result in non-conformance with the standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Link to Active This link will always route to the current Active version of the standard. D8885 Version s – view previous versions of standard. Inch-pound units is the technically correct name for the customary units sstm in the United States. Specimen gripping Instron’s Solution: Tensile Properties of Yarns and Cords. Concrete, Asphalt and Rock. The methods include testing procedure only and include no specifications or tolerances.

WaveMatrix 2 for Dynamic Testing. Work-to-Break of Yarns and Cords. The test results from the two laboratories should be compared using a statistical test for unpaired data, at d885 probability level chosen prior to the testing series.